A vacuum insulating glass unit is engineered for the long service life behind its 15-year manufacturer's warranty — wind load, thermal cycling, and building movement. It can be lost in ten seconds by a forklift touching the wrong corner. Most VIG damage does not happen in service — it happens between the factory and the frame, during receiving, storage, and transport, where nobody is thinking about glass physics and everybody is in a hurry.
The good news: the failure modes are few, well understood, and almost entirely preventable with a short list of habits. This post walks through each stage a unit passes through on its way into the wall, and what keeps it intact at every one of them.
Why the edges are the vulnerable part
A VIG unit is two panes of glass sealed together around the perimeter, with the space between them evacuated and sealed inside a vacuum chamber at the factory — a portless process with no surface extraction port. All of the unit's thermal performance lives in that evacuated gap. The perimeter seal is what maintains it, and the edge of the glass is also, structurally, the most fragile part of any lite — glass fails from its edges, and chips concentrate there.
That combination makes edge damage the defining risk of VIG handling. A chip on the face of the glass is a cosmetic problem. A chip on the edge can propagate a crack, and a crack that reaches the seal means the vacuum is gone. A lost vacuum is not a service event: a unit cannot be re-evacuated on site. That is why an edge chip is a do-not-install condition, not a cosmetic note: quarantine the unit, photograph it, and settle it with the fabricator before the glass goes into the frame. A breached unit is a replacement, not a repair — which is why an hour of careful handling beats any warranty conversation later.
Receiving: inspect before you sign
The receiving dock is where accountability transfers, so it is where inspection matters most. Before signing the delivery paperwork:
- Check every unit's edges and corners first. Run a gloved finger along the perimeter. You are feeling for chips, nicks, and cracks — the defects that matter most.
- Check the frit seal band. The fused glass frit should run continuous and uniform around the perimeter; a chip in the frit band is a flag worth raising before the truck leaves.
- Look across the coated surface at an angle for scratches or coating abrasion.
- Photograph everything, including the delivery paperwork and any defect you find, before signing.
- Note damage on the delivery receipt itself. A defect recorded at the dock is a carrier claim; a defect discovered the following week is a conversation.
A complete receiving checklist, with photographs of what edge damage actually looks like, is in our full Glass Care & Handling guide — free with a trade account from the technical resource center.
Storage: vertical, padded, and off the floor
Glass wants to stand up, and VIG is no exception. Stored correctly, a unit is well protected; stored badly, it can damage itself.
- Store units vertical on an A-frame or padded rack, leaning approximately 5–6 degrees back from vertical, never flat on the floor and never directly on concrete.
- Separate units with soft, full-size separators — never glass-to-glass, and never a small pad that lets one lite bridge onto another.
- Corner protectors on every unit in storage. Corners are where racks, carts, and doorways do their damage.
- Keep units indoors and dry. Standing water against an edge for weeks is hostile to any glazing system; a heated space is best in freezing weather.
One more habit: designate the storage zone before the truck arrives. Units that get "set down for now" in a traffic path are the ones that get backed into by the next delivery.
Transport: slow, vertical, and padded
Most transport damage comes from three sources: hard point contact with edges, vibration, and speed over uneven ground. All three are schedule problems disguised as physics problems — the fix is planning the move before lifting.
- Carry with suction lifters or glass-handling gloves, with two people minimum for anything over a small lite. Lift by the face, never by the edge alone.
- Keep units vertical in transit. Laying glass flat turns every road vibration into a flexing load; standing up, the unit carries load the way it was designed to.
- Pad anything that touches the glass. Straps need softeners at the contact line; racks need full-length cushioning; nothing metal should ever touch a unit directly.
- Walk the route first. Curbs, dock plates, gravel, and rail crossings decide whether the ride is gentle. Slow down for all of them — a few minutes of patience is cheaper than one cracked lite.
Installation: protect the edge to the last minute
The final meters into the frame are where careful units traditionally get ruined, so keep the discipline to the end. Set the unit on setting blocks as specified, keep hard point contacts off the edges, and confirm the frame rebate has the clearance the glazing guide calls for. Never force a unit into a tight opening — pressure at install day has a way of showing up as a stress crack days later, and by then it reads as a product failure when it was a technique failure.
For the full glazing sequence — setting blocks, edge clearance, gaskets, and sealing — see Installing Vacuum Glass: A Guide for Glaziers and Framers, and follow the project's glazing instructions where they differ.
Cleaning: gentle on the coating, gentle on the seal
Cleaning is where good units go to be scratched. Use non-abrasive cleaners and soft cloths, keep blades and scrapers away from coated surfaces, and never direct high-pressure water at the edge seal. A warm-edge perimeter is a sealed assembly, but it is not a place to test pressure washers. Routine inspection while you clean — a glance along the edges and across the coating — is the cheapest early-warning system a glazing contractor can own.
If a unit is damaged anyway
It happens, even to careful crews. The sequence is simple:
- Photograph the damage in daylight, including a shot that shows where it sits on the unit.
- Record the details — unit size, quantity, order or delivery reference, and where in the handling chain the unit was when the damage was found.
- Contact the fabricator before disposing of anything. The unit may need to be inspected, and the photographs you took at receiving may be what settles the claim.
If the damage reached the edge seal, the vacuum is lost, and the telltale sign appears later as fog or droplets between the lites that never wipe off. That failure mode — how to recognize it, and why it means replacement rather than repair — is covered in detail in Why Vacuum Glass Stops Window Condensation.
The bottom line
VIG units ask for only a few habits: inspect at the dock before signing, store vertical and padded at approximately 5–6 degrees from vertical, carry by the face, pad every contact, and never force a unit into a frame. Suction lifters and padded A-frame racks are the main equipment investments — the habits themselves cost nothing. All of them protect a component whose entire value — the vacuum — lives behind an edge seal a few millimeters wide.
The complete field version of this guidance, including the printable four-page PDF, is the Glass Care & Handling guide in our technical resource center — free with a trade account.




