Markets · NYC Retrofits & Local Law 97

Vacuum Insulated Glass Retrofit NYC — Local Law 97 Window Upgrades

Warm-edge vacuum insulated glass upgrades single-pane and aging double-pane windows from the inside — a slim 6.3 mm retrofit that cuts heat loss, energy costs, and Local Law 97 exposure for buildings over 25,000 square feet.

New York City high-rise building facade with rows of windows

The Problem

New York City's Local Law 97 is now enforced. Most buildings over 25,000 square feet carry an annual greenhouse-gas limit and pay $268 for every metric ton of CO₂e they go over — every year, uncapped — with annual reports due each May 1, certified by a licensed engineer or architect. The limits tighten sharply for 2030 through 2034, and again from 2035.

Windows are one of the most overlooked pieces of that math. In much of New York's building stock, glazing is single-pane or early double-pane, and boilers burn extra gas or oil to make up the heat those windows lose — fuel use that counts directly in the building's reported emissions.

The usual fix — a single-pane window replacement across an office building or residential tower — means scaffolding, tenant disruption, and, across much of the city, an exterior appearance that landmark review protects. Owners need an upgrade that changes what the glass does without changing what the building looks like.

Confirm current rules and your building's limit with the NYC Department of Buildings or your compliance consultant.

How Warm-Edge VIG Solves It

Warm-edge VIG bonds two 3 mm glass lites across a vacuum gap of roughly 0.3 mm. The finished standalone unit measures 6.3 mm overall: thin enough to drop into sash rebates cut for single-pane glass decades ago, and the flush frit seal keeps unit depth equal to the glass stack.

That geometry is what makes an interior window retrofit practical. Units re-glaze into existing frames without re-cutting, most of the work happens from the inside, and the facade keeps its original look — which helps with Landmarks Preservation Commission approval in historic districts.

The warm edge matters as much as the vacuum: with no metal bridge through the seal, the inner pane's surface stays warmer — above the dew point in most weather — so winter drafts and condensation largely disappear. With no gas fill, performance does not drift; if a seal ever fails, the loss of vacuum is visible, not a silent decline.

Center-of-glass performance is 0.46 W/m²·K (0.081 Btu/h·ft²·°F) in the standard build and 0.25 W/m²·K in the hybrid — in a unit that carries roughly half the glass mass of the thinnest common triple-pane (24 mm).

Performance Specs

Standard published bases for the THERMGLASS product line — the Architectural Configurator computes whole-window values for your frame.

Profile thickness

6.3 mm standalone (3 + ~0.3 + 3 mm) · hybrid VIG ≈20.3–26 mm

Center-of-glass U-factor

0.46 W/m²·K (0.081 Btu/h·ft²·°F) standalone · 0.25 W/m²·K (0.044) hybrid

SHGC

Coating-specific: 0.62 on the standard build's integral low-E; the US coating library spans 0.22–0.74

Weight (glass-only)

≈15 kg/m² (≈3.1 lb/ft²) for the 6.3 mm standalone — about half a 24 mm triple-pane's ≈30 kg/m² glass mass

Seal & service life

Flush glass-frit edge seal; no fill-gas drift — seal failure is visible, not a silent decline. Manufacturer warranty — 15-year (standalone) / 10-year (hybrid IGU component); terms on request

Frame modeling

Whole-window Uw per EN ISO 10077-1, 20% frame-area fraction by default; sightline inputs adjust the band

Center-of-glass figures are calculation-derived under EN 673 / ISO 10292 — NFRC 100/500 and EN 673 certification testing is in progress.

Certification Path

THERMGLASS reports thermal performance today as calculation-derived values, with certification testing on a defined path: NFRC 100/500 rating and EN 673 type-approval testing are in progress, and ISO 19916-1 — the international standard for vacuum insulated glass units — is the primary standard the vacuum-gap performance is assessed against.

For bid documents and energy models, specify values as calculated per EN 673 / ISO 10292 with certification testing in progress — the honest position until test data lands. The methodology page lists the full standards basis; specification documentation is available on request.

Example Savings

NYC Zone 4A single-pane retrofit scenario — modeled on the published ROI engine at its defaults: 500 sq ft of glazing, natural-gas heat at 92% furnace efficiency with an EPA emission factor of 5.31 kg CO₂ per therm, full installed cost of $18/sq ft, and New York's climate inputs (IECC zone 4A, about 4,450 heating degree days):

Single-pane glass (1.10 Btu/h·ft²·°F — center-of-glass engine baseline)

$1,195/yr energy savings · ≈7.5-year simple payback · ≈4.0 tonnes CO₂ avoided per year

Double-pane low-E (0.45 Btu/h·ft²·°F whole-window)

$539/yr energy savings · ≈16.7-year simple payback · ≈1.7 tonnes CO₂ avoided per year

Over the cap, those same four tonnes are worth about $1,070 a year in avoided fines at $268 per tonne — but only while the building sits over its limit; a building under its cap saves on energy bills, not fines. Scaled to a 25,000 sq ft building converting 5,000 sq ft of single-pane glazing: roughly 40 tonnes a year, about $10,700 a year in avoided fines plus roughly $12,000 a year in energy savings.

Modeled scenario — results depend on the building, its fuel, and its emissions factors. Run your own building in the ROI Engine.

FAQ

Local Law 97 sets an emissions limit for the whole building, not for individual products — there is no LL97-approved window. Lower fuel use means lower reported emissions, and cutting window heat loss reduces the heating load that drives on-site gas or oil combustion. Your compliance consultant or licensed engineer confirms how the savings land in your annual report.

In most cases, yes. The standalone unit is 6.3 mm overall — two 3 mm lites with a vacuum gap of roughly 0.3 mm — sized to drop into rebates cut for single-pane heritage glass; hybrid builds run about 20.3–26 mm for deeper pockets. The Architectural Configurator validates your opening before you commit.

The work happens from the inside and the street-facing appearance is unchanged, which helps with Landmarks Preservation Commission approval. The slim 6.3 mm profile preserves original sightlines, and re-glazing keeps the existing frames. Confirm specifics with your expeditor before filing.

Today's figures are calculation-derived under EN 673 / ISO 10292, and the certification path is defined: NFRC 100/500 and EN 673 type-approval testing is in progress, with ISO 19916-1 governing the vacuum-gap performance. Every published figure is labeled with its basis — nothing is presented as certified until test data is in.

On the engine's modeled New York example, 500 sq ft of single-pane glass upgraded to warm-edge VIG returns about $1,195 a year with a 7.5-year simple payback and avoids roughly four tonnes of CO₂ per year; against double-pane low-E glazing, about $539 a year. Avoided fines at $268 per tonne apply only while a building sits over its limit. Model your own building in the ROI Engine.

Request a Quote

Send your opening schedule — we will return a specification and a budget figure. To model performance first, the Architectural Configurator computes whole-window U-values, condensation resistance, and indicative pricing.