Marine
Modeled: world-cruise charter yacht, bridge re-spec at engine defaults
60 m motor yacht on a mixed-global itinerary — 30 m² of bridge glazing costed against sea-generated power
Modeled scenario using THERMGLASS calculators — not a completed installation. Figures are calculation-derived; see the outcome note at the end of this page.
The Problem
A world-cruise charter program puts a vessel in a different climate every month — northern Europe one season, the Caribbean the next — and the bridge sits at the top of the superstructure taking every degree of it. Unlike a shore building, every kilowatt-hour of bridge conditioning aboard comes off the ship's own generators, so the glazing load is priced at a sea-generated electricity rate several times a land-side tariff. The owner's management wanted the bridge HVAC line item modeled properly before committing to a re-glaze.
The baseline package was standard double-pane IGU at roughly 2.8 W/m²·K whole-unit — the common marine specification. On a mixed-global operating profile the engine's weighted mean interior-outdoor differential works out to 15.3 °C across the year (heating-dominant at 55% of operating time, cooling at 45%), and through 30 m² of bridge glazing that conduction alone drives about 2,879 kWh/year of compressor electricity at the marine HVAC COP of 3.0 — the engine divides the thermal load by the COP before pricing. Clear glass compounds it in warm latitudes: an SHGC of 0.76 admits solar gain across the cooling season at the route's 450 W/m² mean vertical irradiance.
The constraints were the usual marine set. Bridge frames are engineered around the glass fitted at launch and the superstructure is weight-sensitive, so the replacement had to drop into the existing rebates without adding mass high in the vessel. And the premium had to pay for itself against generated power — not a discounted shore tariff — which is the honest yardstick for a yacht that spends its operating hours at sea.
The Solution
The re-spec fits the bridge lites with standalone vacuum glazing — 6.3 to 10.3 mm builds whose flush glass-frit edge seal keeps overall unit depth equal to the glass stack, so the units drop into launch-day rebates with no frame surgery and sit near single-pane weight in the superstructure. Whole-unit performance in the marine frame is modeled at 0.60 W/m²·K, close to a five-fold improvement on the double-pane baseline.
The economics were modeled through the marine ROI engine at its exact default scenario: the 60 m superyacht preset (30 m² of bridge glazing), the mixed-global route profile, 280 operating days per year, HVAC COP 3.0, electric HVAC priced at the engine's sea-generated rate of $0.35/kWh, a representative onboard diesel-generator rate, a $350/m² VIG premium, 5% discount rate, 2.5% energy escalation, over the 20-year vessel design life. At those inputs the engine moves annual HVAC conditioning from 2,878.8 kWh to 616.9 kWh.
The solar side is modeled too, because on a world itinerary it is not a rounding error: dropping SHGC from the clear baseline's 0.76 to 0.62 — the standard build's integral low-E coating — trims the cooling-season solar load by a further 1,905 kWh/year at the route's irradiance profile; coated builds reach 0.28 to 0.40, so the modeled solar savings are conservative. And the same physics does the comfort work the charter crew notices first — with almost no gas in the vacuum gap, the inner lite sits near cabin temperature, so the watch keeps a clear, dry bridge in cold latitudes without the radiant chill zone of conventional glazing.
Modeled Outcomes
Figures are modeled outputs calculated from published methodology and the THERMGLASS marine ROI engine at its exact default inputs — not laboratory or field measurements. Run the linked calculator with your own vessel class, route profile, and fuel basis for project-specific numbers.
Avoided conditioning
≈4,167 kWh/yr
Engine output at the default scenario: 2,262 kWh of conduction avoided (1,244 heating + 1,018 cooling) plus 1,905 kWh of reduced solar gain — annual bridge HVAC conditioning falls from 2,878.8 to 616.9 kWh of compressor electricity at COP 3.0 — the engine divides the thermal load by the COP, so the $0.35/kWh generator rate prices delivered energy.
Annual savings
≈$1,458/yr
Priced at the engine's sea-generated electricity rate of $0.35/kWh, a representative onboard diesel-generator rate — the onboard rate that makes each avoided conditioning kilowatt-hour worth roughly 2.5× a shore-side one.
Simple payback
≈7.2 yr at defaults
$10,500 of glazing premium ($350/m² across 30 m²) against $1,458/yr — the engine's honest default answer before rebates, route changes, or tariff movements; the linked calculator prices your vessel.
20-year NPV
≈+$11,810
At the engine defaults: 5% discount rate, 2.5% energy-price escalation, 20-year analysis period. Alongside ≈2.5 t CO₂/yr avoided at the 0.60 kg/kWh blended generator-plus-shore-power factor — ≈50 t over the period.
Put numbers on your project
Model the same glazing decision for your own project — dimensions, climate, and rates in, project-specific savings out.
Technical Reading
Vacuum Glass for Marine Vessels: Condensation and Weight
Bridge glass fogs from the first cold current. How vacuum glazing keeps wheelhouse glass dry and light — and what it changes for fuel and refits.
Read the guideVacuum Glass for EU and UK Marine Projects
Metric specs for EU and UK vessels: EN 673 and EN ISO 10077-1 values, acoustics, polar conditions, fire advisory and EUR pricing.
Read the guideHow to Calculate Vacuum Glass Payback: The Complete Guide
A step-by-step method for annual savings, simple payback and NPV, with a worked example from the THERMGLASS ROI Engine.
Read the guideThermal Insulation Compared: Vacuum Glass, Triple-Pane, Low-E IGU
Side-by-side analysis of U-values, SHGC, weight, and thickness across glazing types — with data grounded in EN 673 and NFRC 100 test standards.
Read the guideSound, Condensation, Payback: Vacuum Glass vs. Triple-Pane
The engine-backed verdict: vacuum glass vs. triple-pane on U-values, weight, acoustics, condensation margin, and payback at exact default inputs.
Read the guideSpecifying a similar project?
Talk to the engineering team about glazing your project.
Contact THERMGLASS