RV & Mobile
Modeled: camper van re-glaze, four-season build
Class B camper van conversion — factory wall openings re-glazed for four-season touring
Modeled scenario using THERMGLASS calculators — not a completed installation. Figures are calculation-derived; see the outcome note at the end of this page.
The Problem
The van was built for four-season touring, but its factory windows were not. In cold weather the single-pane glazing runs far below cabin dew point, and in a space this small the moisture load is relentless — two people cooking, sleeping, and breathing in a few cubic metres of insulated box. Every winter morning starts with wiped windows, wet bedding near the glass, and a damp microclimate the ventilation fan never quite clears.
The energy math compounded it. Cabin heat in a camper van comes from propane or a 12-volt diesel-style heater, and every watt conducted out through the glass has to be replaced from a house battery and a fuel tank with hard limits. On a winter boondock night the windows were the single largest hole in an otherwise well-insulated envelope.
The physical constraints ruled out the obvious upgrade. RV wall openings are shallow — thin extruded frames set into sandwich-panel walls — so a triple-glazed unit built for comparable performance simply has nowhere to go. And in a vehicle, every kilogram of glass added above the axle is paid for out of payload.
The Solution
The refit re-glazes the factory window openings with 6.3 mm standalone vacuum insulated glass. The portless glass-frit edge seal is flush, so the unit's overall depth equals the glass stack itself — it sits in the same shallow rebate the single-pane factory glass occupied, with no frame surgery and no wall rebuild.
The makeup carries a high-performance low-e stack, specified through the RV configurator against the size limits and safety-glazing requirements of the application. Center-of-glass performance is calculated, not laboratory-measured: 0.46 W/m²·K for the published base — a figure that already includes the unit's integral low-E coating, with SHGC tuned per the selected coating — on the EN 673 / ISO 10292 calculation basis used across this site. At roughly 15 kg/m², the units weigh about half of a triple-glazed build for comparable performance — payload spent on water and gear, not on glass.
With almost no gas in the cavity to carry heat across, the inner lite tracks cabin temperature instead of road temperature — the same surface-temperature mechanism as every other vacuum build on this site. In a small, humid cabin that margin is the difference between condensation and clear glass, and the heater cycles less because the glass is no longer a permanent cold sink at every window.
Modeled Outcomes
Figures are modeled outputs calculated from published methodology — not laboratory or field measurements. Configure your own openings in the linked configurator for project-specific performance.
Glazing depth
6.3 mm
Flush, portless frit seal: overall depth equals the glass stack, so the unit fits the shallow wall openings triple glazing cannot. Retrofit into factory rebates, no frame surgery.
Glass mass
≈15 kg/m²
About half the mass of a triple-glazed unit built for comparable thermal performance — payload preserved in a vehicle where every kilogram counts.
Inner surface temp
≈63 °F at 70 °F / 0 °F
Modeled inner-surface temperature at the published design condition — above the dew point of a small, high-humidity cabin, where the fog cycle used to start before sunrise.
Cabin heat loss
≈93% lower at the glass
Modeled from the U-value comparison against the single-pane factory glass (0.081 vs ≈1.10 Btu/h·ft²·°F at the center of glass) — the conductive component the house batteries and heater no longer have to replace. Project-specific figures via the linked configurator.
Put numbers on your project
Model the same glazing decision for your own project — dimensions, climate, and rates in, project-specific savings out.
Technical Reading
RV Windows: Why Vacuum Glass Belongs in Your Rig
About 50% lighter than a 24 mm triple-pane unit with better insulation: passive defogging, four-season comfort and a fit for existing frames.
Read the guideRetrofit Glazing: Slim Vacuum Glass for Old Windows
Retrofit glazing without rebuilding frames: how 6.3 mm vacuum insulated glass replaces single panes in original sashes — options, limits, and heritage considerations.
Read the guideVacuum Glass vs. Triple-Pane: U-Value, Weight, Cost
Vacuum glass vs. triple-pane compared: center-of-glass U-values, unit depth, weight, and installed-cost drivers — the spec-level comparison for your next project.
Read the guideVacuum Insulated Glass Explained: U-Values, Specs, Uses
How vacuum insulated glass reaches triple-pane-class U-values in a 6.3 mm build: the physics, the spec numbers, and where VIG earns its keep.
Read the guideSpecifying a similar project?
Talk to the engineering team about glazing your project.
Contact THERMGLASS