Field Guide

Condensation and Moisture for Vacuum Insulating Glass

When interior condensation is normal, when it signals an edge-seal problem, how low U-values change condensation behavior, and practical humidity management for VIG units.

Condensation forms where a surface falls below the dew point of the air next to it. On a window, that surface is usually the room-side glass or the frame. Which surface condenses first - and how often - is a direct readout of the glazing's thermal performance.

Vacuum insulating glass changes that readout: the room-side lite runs much closer to room temperature than single glass or clear double glazing, so the interior surface rarely reaches the dew point. Most condensation you will see around a VIG unit is transient and benign. A few patterns, though, are worth acting on - and one in particular (moisture between the lites) means the unit itself needs attention.

Why condensation appears where it does

Every condensation question comes down to two numbers: the temperature of the surface and the dew point of the air beside it. If the surface is colder than the dew point, water forms. Everything in this guide follows from that one rule.

The room-side surface of ordinary glass runs much colder than the room, so it is usually the first surface in a room to condense. The room-side surface of a vacuum insulating glass unit runs much closer to room temperature - which moves the whole question to a different place on the window and, mostly, to different days.

  • Warm air holds more moisture than cold air. The dew point is the temperature at which that moisture starts to condense out.
  • A surface condenses water when its temperature falls to or below the dew point of the air touching it.
  • Glass surface temperature sits between indoor and outdoor conditions; a glazing's U-value decides how close to indoor it stays.
  • High indoor relative humidity raises the dew point - the same surface condenses earlier. That is why condensation risk is highest on cold mornings after humid evenings.

How VIG's low U-value changes condensation behavior

A glazing's center-of-glass U-value sets how much heat flows from the room to the outer lite. With a very low U-value, little heat flows - so the room-side lite stays near room temperature while the outer lite runs near outdoor temperature.

That temperature split has two visible consequences. Inside, the room-side surface rarely gets cold enough to condense water, even in weather that fogs ordinary windows. Outside, on clear cold nights, the outer lite can fall below the outdoor air temperature by radiating to the sky - so exterior condensation or frost appears on very efficient glazing. Neither is a fault; both are readouts of performance.

  • A warmer room-side lite means interior condensation becomes rare at normal indoor humidity levels.
  • The warm-edge perimeter detail keeps the edge band closer to room temperature as well, so the classic cold-edge condensation pattern of metal-framed double glazing is much reduced.
  • Exterior condensation can appear on clear, cold nights: the outer lite radiates heat to the sky and briefly falls below the outdoor dew point. It clears as the glass warms and is a sign the unit is insulating, not a defect.
  • Because the interior surface is warm, persistent interior condensation on a VIG unit points away from the glass and toward the room (humidity), the frame, or the installation detail.

Normal condensation - no action needed

These patterns are expected with high-performance glazing and need no intervention beyond normal humidity management.

The common thread: the condensation is transient, it sits on surfaces you can wipe, and it matches weather or activities. It returns on humid mornings and leaves with ventilation - it does not persist day after day in the same spot.

  • Brief fogging during and after humid events - showers, cooking, large gatherings - that clears within an hour as the air dries or ventilates.
  • Exterior condensation or light frost on clear, cold mornings, which disappears as the sun rises or the air warms.
  • Condensation on adjacent poorer-performing glazing - doors, skylights, older windows - while the VIG units stay dry.
  • A line of condensation on the frame itself where metal trim or hardware bridges to the outside; the glass is not the cold surface.

When condensation signals a problem

Three patterns deserve action. Two of them are installation or building issues you can fix; one is a unit issue only the fabricator can resolve.

The key distinction is location: moisture you can wipe is on your side of the glass, and moisture you cannot wipe is inside the unit.

  • Moisture between the lites - fog, mist, or droplets visible behind the glass surface that never wipe off and do not move with the weather. The edge seal has been breached; the unit is replaced, not repaired. Contact THERMGLASS with photographs and unit details.
  • Interior condensation that returns every day in the same place, especially along the bottom rail or at one edge, while the rest of the room is dry. Investigate the frame detail, gasket, setting blocks, or a possible leak at that location.
  • Water collecting or ice forming at the sill with evidence it is running down from the glazing - check that weep and drainage paths are open before assuming a glass problem.
  • Condensation spreading to walls, ceiling corners, or other cool surfaces in the same room - the room's humidity is the driver, not the glazing. Treat it as a ventilation and moisture-management problem, because mold risk grows with it.

Diagnosing: three questions

Most condensation reports resolve with three questions - where, when, and what shape. Answering them before calling saves a site visit in most cases.

  • Where is it? On the room-side surface (wipe-able) is a room or frame question. Between the lites (never wipes off) is a unit question. On the exterior is almost always normal.
  • When does it appear? During and shortly after humid activities or on cold clear mornings is transient and normal. Every day, in the same place, regardless of weather is a pattern to investigate.
  • What shape is it? A uniform film across the surface follows room humidity. A band at one edge or the bottom rail follows a cold path - frame, gasket, or drainage.
  • For a between-lites finding, photograph the unit in daylight, note the location of the fog pattern, and have the unit's size and order details at hand before contacting THERMGLASS.

Humidity management

Good glazing reduces condensation risk; it cannot remove moisture from the air. The last layer of protection is managing how much water vapor the indoor air carries.

The warmer the room-side glass surface, the higher the humidity the room can carry before condensation - that is VIG working for you. But every surface has a limit, and sustained high humidity brings mold risk regardless of the glazing.

  • Track indoor relative humidity with an inexpensive hygrometer; aim for roughly 30-45% at typical room temperatures.
  • In deep cold, target lower: roughly 25-30% when outdoor temperatures sit near or below -12 °C (10 °F). These figures are rule-of-thumb guidance, not code requirements.
  • Run kitchen and bathroom exhaust fans during and for a while after moisture-generating activities; ventilate briefly and fully rather than leaving windows cracked all day in freezing weather.
  • Avoid trapping humid air against the glass: heavy curtains closed tight over cool surfaces hold a humid microclimate against them; leave some air path.
  • Keep weep and drainage paths open so the glazing system can drain and dry as designed.
  • Seasonal check: when heating starts in autumn, expect a brief adjustment period while the building dries out - and re-check the hygrometer before concluding anything is wrong.

If you see moisture between the lites

A breached edge seal is not a maintenance item - the unit is a closed system and is replaced, not repaired. The steps below make the replacement smooth.

  • Do not attempt to open, re-dry, or re-seal the unit. The vacuum is sealed at the factory and cannot be re-evacuated on site.
  • Photograph the fog pattern in daylight, note the unit size, quantity, and order or delivery details, and contact THERMGLASS.
  • Keep the unit installed and in service while the assessment proceeds - a fogged unit still glazes, seals, and holds its structure; only its thermal performance is lost.
  • Where the installation detail itself is suspect - standing water at the sill, a soaked gasket, a blocked weep - resolve that in parallel, because it can damage the replacement too.

Frequently asked questions

Is condensation on the outside of my VIG windows a defect?

No. Exterior condensation on high-performance glazing is a known and benign phenomenon: on clear, cold nights the outer lite radiates heat to the sky and can fall below the outdoor dew point. It clears as the glass warms, and it is a sign that heat is staying inside the building - not a defect.

How do I tell room-side condensation from moisture inside the unit?

Room-side condensation sits on the surface you can touch and wipes away. Moisture between the lites sits behind the glass surface - it never wipes off, and it usually shows as fog or droplets that do not move. Between-lites moisture means the edge seal has been breached; contact THERMGLASS with photographs and unit details.

What indoor humidity should I keep in winter?

As a rule of thumb, keep indoor relative humidity around 30-45% at typical room temperatures, and lower in deep cold - roughly 25-30% when outdoor temperatures sit near or below -12 °C (10 °F). These are comfort-and-condensation guidance, not code requirements. A simple hygrometer takes the guesswork out.

Does VIG eliminate interior condensation?

It greatly reduces interior condensation by keeping the room-side glass surface much closer to room temperature, but no glazing eliminates condensation if the air's dew point is high enough. Sustained high indoor humidity will condense on some surface - and brings mold risk - so humidity management and good glazing work together.

Download the printable field guide

The four-page PDF version of this guide - with the quick-reference diagnosis table - is available as a gated download from the technical resource center. A free trade account is required.

Document TG-COND-2026-01, Rev 1 · 4 pages · PDF